Electrical equipment and appliances Hyundai Getz

Electrical Equipment Specifications
Battery Type MF45A4 MF55A4 MF68A4 Ampere hours (5HR) Over 36 Ah Over 44 Ah Over 54 Ah The current strength when cranking the crankshaft of a cold engine 410A 500 A 600 A...

Troubleshooting of control and measuring instruments
Feature Probable Cause Elimination method Tachometer not working Blown fuse #7 (10 A) Check for short circuit and replace fuse Faulty tachometer Check the tachometer...

Troubleshooting the Lighting System
Feature Probable Cause Elimination method Only one ambient light is off Bulb burnt out Replace lamp Lamp socket defective or damaged or shorted to «mass» wiring Check...

Troubleshooting the wiper switch
Feature Probable Cause Elimination method Wipers not working or returning to off position Blown fuse Check for short circuit and replace fuse Faulty wiper motor Check...

Relay location and test
Relay test (type A) Check for continuity between relay terminals. 1. When applying voltage from the battery terminals to contacts 1 and 4 of the relay, there must be...
There is 1 a comment

Relay in the car
Relay test (type A) Check for continuity between relay terminals. 1. When voltage is applied from the battery terminals to relay contacts 2 and 3, there must be...

Fuses and their locations
Fuses are used to break the circuit when the current reaches a certain value, in order to protect elements and wires that can be damaged by too much current. A sudden...

Ignition lock — removal, installation and inspection
Removal and installation 1. Disconnect a wire from the negative plug of the storage battery. 2. Turn out two bolts, disconnect a socket of the switch of a sound signal...

Instrument cluster — removal, installation and inspection
Removal and installation 1. Disconnect a wire from the negative plug of the storage battery. 2. Turn out the screw and remove a frame of a combination of devices. 5....

Control devices — removal, installation and check
Location of sensors of control devices: 1 - vehicle speed sensor; 2 – a combination of devices; 3 – the switch of a control lamp of a parking brake; 4 – the switch of a...

Parking brake position switch
The Hyundai Getz inching type parking brake position switch is located under the parking brake lever. Adjustment is made by moving the switch bracket up or down with the...

Multifunction switch — removal and installation
Removal and installation When removing the multi-function switch on vehicles equipped with an airbag, be careful and comply with the following conditions. Warnings! Do...

Sound signal — removal, installation and check
1. Open a cowl, turn out two screws and remove facing of the cowl lock. 2. Turn out a bolt and remove a sound signal. 3. Installation is carried out in the reverse order...

Audio system — removal and installation
Removal and installation 1. Disconnect a wire from the negative plug of the storage battery. 2. Turn out two screws and two bolts of fastening of the bottom facing of...

Speakers — removal, installation and inspection
Front speakers 1. Turn out screws of fastening of the internal handle of a door, disconnect from the handle of draft of a drive of the lock and blocking of the lock and...

Antenna — removal and installation
1. Use a flat-blade screwdriver to remove the dome glass from the overhead console. 2. Turn out two screws, disconnect a socket and remove the console. 3. Turn away a...

Rear window heater
The defrosting of the rear window is carried out by a heater, which is a series of parallel conductors sprayed onto the glass. When an electric current is passed, the...

Windshield wiper — removal, installation and inspection
Withdrawal 1. Turn away nuts and remove levers of screen wipers. Tightening torque: 7–11 Nm 4. Installation is carried out in the reverse order of removal. Checking the...

Lighting devices — removal and installation
Instruments and controls for the vehicle lighting and light signaling system: 1 - fuse box and relay in the passenger compartment; 2 – the switch of a signal of braking;...

Headlights — removal and installation
1. Disconnect a wire from the negative plug of the storage battery. 2. Turn away two bolts of fastening of the top facing of a forward bumper. 4. Installation is carried...

Headlight adjustment
Headlights must be adjusted using special equipment and in accordance with the equipment manufacturer's instructions. Rotate the adjustment wheels one by one to adjust...

Airbags (SRS)
The Hyundai Getz car is equipped with an auxiliary security system, better known as airbags. The system consists of sensors installed at the front of the vehicle,...

Driver's airbag and coil drive
Withdrawal 1. Disconnect a wire from the negative plug of the storage battery. Warning! Before servicing the airbag system, make sure that at least 30 seconds have...

Coil spring
The coil spring consists of two twisted coils. It is installed between the steering column and the steering wheel and allows the steering wheel to rotate while keeping...

Front passenger airbag
Withdrawal Warnings! 1. Do not disassemble or repair airbag system components. 2. If the airbag has been dropped or has been exposed to water or oil, or if there are...

Seat belt pretensioner
When the vehicle is involved in an accident at a certain angle with respect to the frontal impact, the gas generator is ignited by an electrical signal from the SRSCM....

Seat belt load limiter
The load limiter is designed to reduce the impact force of the driver and front passenger on the fastened seat belts during a collision. If the collision force reaches a...

Immobilizer — principle of operation
The immobilizer system consists of a passive transponder (for mutual recognition), mounted in the car key head, and the SMARTRA antenna unit (SMARt TRansponder Antenna)....

Designation and power of lamps
No lamp name Power, W 1 headlights (high beam / low beam) 60/55 Front marker lights 5 2 Front fog lights (optional equipment) 27 3 Front direction indicators 21 4 Side...